Whirlpool EDR1RXD1 Water Filter: Replacement Tips & Guides

💧 Does your fridge water taste off? Smell strange after a filter change? Or is the flow just a trickle?

You're not alone, and the fix is simpler than you think. This complete guide covers everything about the Whirlpool EDR1RXD1 water filter: what it does, which fridges use it, how to install it, and when to replace it.

What Is the EDR1RXD1 Water Filter?

The Whirlpool EDR1RXD1 (also sold as the EveryDrop Filter 1) is an OEM refrigerator water filter designed to deliver clean, great-tasting water directly from your fridge dispenser and ice maker.

✅ NSF Certified

Certified to NSF/ANSI Standards 42 & 53

💧 Removes 28+ Contaminants

Including lead, chlorine, cysts & more

🧊 Ice Maker Compatible

Filters water for both dispenser & ice

📅 6-Month Lifespan

Or 200 gallons — whichever comes first

It uses activated carbon block technology to reduce chlorine taste and odor, lead, mercury, asbestos, and dozens of other contaminants, giving you cleaner, safer drinking water without a separate filtration system.

Which Refrigerators Use the EDR1RXD1 Filter?

The EDR1RXD1 is compatible with a wide range of refrigerators across multiple brands. It fits models from Whirlpool, Maytag, KitchenAid, Amana, Jenn-Air, and Samsung (select models).

🔍 Compatible Refrigerator Model Examples

Whirlpool WRS325SDHZ, WRF535SWHZ, WRF757SDHZ
Whirlpool WRS571CIHZ, WRS588FIHZ, WRX735SDHZ
Maytag MFI2570FEZ, MFT2772HEZ, MFX2570PEM
KitchenAid KRFC300ESS, KRFF300ESS, KRSC700HPS
Amana ASD2575BRS, ASI2575GRS, ABB1924BRM
Jenn-Air JFC2290VEM, JFFCC72EFS

⚠️ Always verify compatibility using your fridge's model number (found inside the door frame) before purchasing. Model lists can vary by production year.

EDR1RXD1 vs W10295370A: What's the Difference?

This is one of the most common questions we get. Here's the short answer: they are the same filter. The W10295370A is the older part number, and the EDR1RXD1 is the updated replacement under the EveryDrop branding.

Feature	EDR1RXD1	W10295370A
Brand	EveryDrop by Whirlpool	Whirlpool OEM
NSF Certified	✅ Yes (42 & 53)	✅ Yes
Contaminants Reduced	28+	28+
Filter Life	6 months / 200 gal	6 months / 200 gal
Status	✅ Current model	🔄 Superseded

If your fridge calls for a W10295370A, you can safely use the EDR1RXD1 as a direct drop-in replacement.

How to Replace the EDR1RXD1 Water Filter (Step-by-Step)

Replacing this filter takes under 5 minutes — no tools required. Here's how:

Locate the filter

The EDR1RXD1 is typically located in the upper-right corner inside the fridge compartment.

Push and turn to remove

Push the old filter in slightly, then turn it counterclockwise about a quarter turn and pull it straight out.

Remove the cap

Transfer the blue end cap from the old filter to the new one (if your model requires it).

Insert the new filter

Align the new EDR1RXD1 with the housing, push in, and turn clockwise until it locks into place.

Flush the system

Dispense and discard 2–3 gallons of water (about 5 minutes of running) to clear air and carbon fines.

Reset the filter indicator

Hold the "Filter Reset" or "Water Filter" button on your fridge's control panel for 3 seconds until the light turns green.

💡 Pro tip: Place a towel under the filter housing before removal to catch any drips.

How Often Should You Replace the EDR1RXD1?

Whirlpool recommends replacing the EDR1RXD1 every 6 months or 200 gallons, whichever comes first. But your actual replacement schedule may vary.

🔴 Replace sooner if you notice:

Water tastes or smells off (chlorine, musty, or metallic)
Noticeably reduced water flow from the dispenser
Ice has an unusual taste or odor
The filter indicator light turns red or orange

🟢 You may be able to wait longer if:

Your household uses very little filtered water
Your municipal water quality is already high
Water taste and flow remain normal

⏰ Tip: Set a recurring 6-month reminder on your phone right after each replacement so you never forget.

Common Problems & Fixes

💧 Water tastes bad after filter change

This is almost always caused by not flushing the system. Run 2–3 gallons through the dispenser after installation. The taste should clear within 24 hours.

🚿 Low water pressure from dispenser

Check that the filter is fully locked in place. If pressure is still low, the filter may be clogged (replace it) or there may be a kinked water line behind the fridge.

❌ Filter not fitting or leaking

Ensure you're using the correct filter for your model. A leaking filter usually means it's not fully seated — remove and re-insert, making sure it clicks into place.

🔴 Filter light won't reset

Hold the reset button for a full 3–5 seconds. On some models, you may need to press and hold "Options" + "Water Filter" simultaneously. Consult your fridge manual for the exact reset sequence.

🌫️ Water smells musty or like refrigerator

This can happen if the filter sat unused for a long time. Flush 3–4 gallons through the system. If the smell persists, check the fridge interior for odor sources (old food, spills).

Best Alternative Filters for EDR1RXD1

If you're looking for a compatible replacement at a different price point, here's what to know about genuine vs. generic filters:

🏆 Genuine EDR1RXD1 (EveryDrop by Whirlpool)

Best performance, guaranteed compatibility, full NSF certification. Ideal if water quality is a top priority for your household.

💰 Compatible Third-Party Filters

Often 30–50% cheaper. Look for filters that are NSF 42 & 53 certified and explicitly list your fridge model as compatible. Avoid uncertified generics.

⚠️ Warning: Counterfeit filters are common online. Always buy from authorized retailers. Fake filters may not remove contaminants and can void your fridge warranty.